Category Archives: SDCard

Pretty on the outside and ugly on the inside prototype

By | | , , , , , , , , , , , , , ,
Leave a comment

So I’ve been busy doing a bunch of computer maintenance and looking into other things I’ve neglected while building the roaster so it’s been a bit slow.  I decided I wanted to start gluing corners together and drilling some holes to see how the case goes together so I can eventually get back to fixing the issues with the roast controller case.  Over the past several weeks I soldered together all of the boards, made wiring harnesses and figured out a bunch of “oops” moves I had made designing things when I got rushed for time.

Turns out I was not able to get stand offs locally in the sizes I had wanted so the heights are all screwed up where I placed holes on the outside surfaces.  I also forgot to specifically allocate power for the exhaust fan in the original design BUT I did have “Spare” pins allocated. The fan I ordered also was not the right size for the hole template I had used (Inside fan dimension vs outside screw / case dimension)… neither of them were actually labeled right the way every other fan I have is sized.

So with everything screwed or harnessed in place this is what I have for the Arduino…

The Arduino wired for Coffee Roaster control

It is a MEGA2560 mounted on a Crib for Arduino.  On top is an Ethernet Shield w/ microSD slot.  Then I used a variety of crimped headers to connect to some of the pins on the MEGA and on the ethernet shield.  I have twenty five lines in the bundle going to the Arduino.  I had some spare 10 strand cables from a project at Halloween and no 25 strand cables to use so I used one of those cable wraps to keep the all together after connecting DB25 to one end and header pins to the other.  Once the lid for the crib for Arduino is in place it then connects to the back of the enclosure.

Wiring Harness connecting to the back of the controller enclosure

As you may notice the sockets I was using for connecting the power out are the type that snap in.  The majority of these will not snap into most laser cut plastic sheets and instead are designed for aluminum cases.  The plug to the right on the other hand screws in.  These work great with a variety of thicker locations.  The fan was originally going to be on the inside with a wire cover on the outside but with the wrong size fan hole in use I had the wrong cover to fit the fans that I had that would fit the hole.

For the DB25 connectors it turned out good that I had decided to use a cut out pattern  that had the holes on the side for the anchoring hex nuts rather than just having them cut out so that I could mount them to the socket and anchor the connector.  Since the stand offs were too short they don’t allow me to anchor the PCBs to the bottom plate.  Instead I had to screw them to the back plate using normal screws and with the burnt circles on the laser cut work I had to use some washers too to keep it sturdy.  This is what the back plate looks like.

Rear Panel of controller

This panel includes – One non-filtered switched 15Amp Power Entry module, 2 snap in 15 amp convenience plugs, 1 5VDC fan, 2 DB-25.  The left one is the main guts for the LCD, TRIAC control, potentiometers, thermocouple, and a variety of other sensors.  The right includes all the non-essential stuff for backlighting all the buttons on the button pad and a few other things including spare wiring.  You cna see just a screw on the right since it was relatively intact and so it won’t block the DB25 plug being used.  The right DB25 has washers and screws in place.  These are primarily used to attached the PCB in place attached to the back side.

Next up is the inside view of the electronics area:

Rear View of the Back Panel

Rear view of the back panel.  I need to shrink up the crimp connectors around the wire  (they shrink like heat shrink tubing but is actually much firmer).  Also the connector on the right side (the switched power entry module) should have the screws more securely fastened with nuts and washers but this is mainly just a test to ensure it all fits together and then allow me to focus on some programming for a while to see if I can get more working and develop menus etc.  The clear acrylic bar is used to anchor the corners better.  I need to change the locations of the screws since I could not find screws the size I wanted without spending way too much for large quantities of them on the internet and having them shipped to me etc.  The thermocouple board on the right had the same issue with the stand offs so it is just floating loose in there right now.  I need to find somewhere to get the Omron thermocouple sockets where I dont need to order them by the 1000s since it looks like Ryan McLaughlin has stopped selling things on his site when they (used to) have problems getting the newer MAXIM thermocouple chip.  They’re all over the place now but he hasn’t restarted his store up so I don’t know the deal there.

Here is the view down into the enclosure from above:

Top view into enclosure

With the cover on:

Front panel installed on enclosure

Front panel running

Front Panel Running

When I send it back out again for a new case I hope to have a different board to install that will be switching the smaller breakout boards being designed onto the circuit board as well as add a power supply and possibly having an arduino board mated on top of the circuit board perhaps to bring more of the electronics inside.  I might want to try to get a Digilent board perhaps to try converting to it as a transition between Arduino and PIC32 before I completely switch to a dedicated PIC32.

I’ve also been looking at possibly creating a dedicated PC application to communicate with it directly via USB and over ethernet.  I am toying around with the “QT/QML” language but havent gotten too far with it.  I may just go back to Processing though.

Arduino roaster controller with zero crossing dimmer

By | | , , , , , , ,
Leave a comment

With all the time I’ve put into the Pic32 roaster I’ve always had this nagging worry that any of my sensors may have had damage during testing. When you try to get something working and keep getting gibberish you need to find a way to rule that out. As a result I decided to purchase an Arduino a few months back to confirm everything works. Turns out (so far) that everything IS actually working and I didn’t damage any sensors.  In the months I’ve been working with the Arduino I’ve actually learned a few reasons why some of the sensors didnt work on the PIC32 the way I had programmed them because learning to program an Arduino is sooooooooooooooooo much easier and better documented for “average people” to figure out compared to reading the hundreds of pages of technical manual for the PIC32 that isn’t ACTUALLY even finished being written yet.  There is a ton of code out there to test every single sensor I’ve purchased so far on Arduino. In addition I decided it would be a great way to start the dimmer using zero crossing detection in a system that runs outside the PIC32 before I convert it.

My intention is to get basic functions working on Arduino, then get the PIC to talk to the Arduino to send it commands to switch power by itself while the PIC reads all the sensors and logs data and then decides what to do as it comes from the Arduino.  Finally it will eventually be migrated entirely to PIC32 when I learn more about the interrupts on PIC32. At the moment I’ve put together a board that takes in 120VAC and uses Q4015L5 Triacs and MOC3052 drivers to control power to two receptacles. It reads the zero cross on my power using a H11AA1 and gets an interrupt used to trigger power switching. During my initial testing I confirmed the zero cross detection circuit worked and switching the triacs manually on or off worked without  regard to the zero cross state. It unfortunately didn’t seem to actually switch automatically for some reason when I wanted it to dim.  After a few days of testing I realized the Arduino Mega and the Uno had the interrupt timer pins in different places.

Since this is the first mains power circuit I’ve worked on I started running it with a variac out in the garage (and then fed that out into the driveway at the end of an extension cord…) and gradually turned the power up from 0 to 120VAC testing each section as I built it to ensure nothing arced or got hot or burnt up.  During late November I hooked it to the Arduino and got it to begin adjusting fan and heater under PC control as well as using two separate knobs.  Later in December and January I got it to begin logging to SD memory and following a programmed profile.  After that I added a bunch of additional environmental sensors and mounted it in a RadioShack project case.

 

First working prototype in Radioshack Project Case

I’m now at a stage where I’m looking to consolidate the various sensor cards either down onto a circuit board or attached to a set of pins directly.  I’ve grown tired of accidentally unplugging random wires carrying it back and forth from the garage to my office area and out to the kitchen stove / vent at various stages.  My hope is to shrink it down to a much less complicated arrangement being mostly on a single circuit board and interfaced by a few short cables to the Arduino.  It’s a bit complicated currently and getting worse.

Jumble of Arduino stuff

For the Arduino I’m using the MEGA 2560.  It is attached to the power control box pictured above via the DB25 cable.  At this time the box only controls power but I’ve mapped out pins on the DB25 to use for future boards to allow sensor breakout boards from a variety of DIY electronics companies to plug into them.   I’ll break this out to various header pins that match various breakout boards so they can be directly attached.  I’ll probably also design positions for eventually soldering chips directly to a board later once I order them when I’m further along and jumper the headers into those sections.  This will let me test a circuit on the board while still ensuring it actually works with the breakout board first.  The board will be designed to replace the items in the RadioShack box using SMD parts in some cases where cheaper and more convenient to shrink the board down smaller.  I hope to have it all shrunk down and consolidated to a single board with a DB25 connector to get to an Arduino I’ll be mounting inside an Arduino Crib case.

More logging… and floating math.

By | | , , , , , , ,
Leave a comment

Two nights ago I managed to finally get the screen that shows graphs to draw the current temperature up in the corner on top of the graph.  Most of the problem was figuring out how to convert the “float” numbers to characters.

I needed to feed this into Microchip’s Graphics Library and accommodate “unicode” characters to get the “degree” symbol on the screen eventually.  Instead of typing a string as string=”Hello There”; it ends up being string={‘H’, ‘e’, ‘l’, ‘l’, ‘l’, ‘o’, ‘ ‘, ‘T’, ‘h’, ‘e’, ‘r’, ‘e’}; which ends up being an array of character values.

A float is a decimal number.  In this case 3 digits for hundreds, a decimal position, and 3 more digits for numbers.  The sensor is kicking out two digits and I’m adding readings together, averaging them, and then rounding up or down with the extra positions in some places.  The PIC32 unfortunately does not have a floating point calculation area in its brain resulting in it “compensating” for it by automatically sliding all the other numbers around using complicated things called mantissa and a few other things I really don’t want to deal with.

The reason I don’t want to deal with them is actually NOT because it is complicated (which it is) but because since it is compensating when you divide a float it has to do MANY cpu cycles for it to compensate and come up with the answer.  It is ACTUALLY easier to multiply the float by 100, 1000, 10,000 etc and insert that number into an integer data type.  Integers can be divided, multiplied, subtracted, etc without worrying about how the numbers line up and doing crazy compensating.  They just don’t end up with a decimal.

If you have a temperature of 175.25 degrees fahrenheit you multiply it by 1000 which equals 175250.  This maintains all of  required digits as a whole number and gives extra space for “rounding” down below.

The issue with the graphics library you need to use a font for every character and take into consideration symbols like degrees etc.  This means it is not simply just a “character” but you need to allocate for all the extra stuff.  This results in a larger space for each character.  To me it looks like a single character in XChar is actually two positions instead of one to leave extra room for the fancy characters to be allowed for.  To convert text strings or float numbers into characters that can be handled by the library you have to load them into an array.  This array to convert the above number (float averaged=175.25)  looks something like this:

int showtemp[8];
showtemp[0]=averaged*1000; //175250

showtemp[1]=showtemp[0]/100000; //175250/100000 = 1 in integer
showtemp[2]=showtemp[0]/10000-(showtemp[1]*10); //175250/10000 = 17.  and then 17- 1*10 = 7 in integer
showtemp[3]=showtemp[0]/1000-(showtemp[1]*100)-(showtemp[2]*10); 175250/1000 = 175 and then 175 – 1*100 – 7*10 = 5
showtemp[4]=showtemp[0]/100-(showtemp[1]*1000)-(showtemp[2]*100)-(showtemp[3]*10); // etc
showtemp[5]=showtemp[0]/10-(showtemp[1]*10000)-(showtemp[2]*1000)-(showtemp[3]*100)-(showtemp[4]*10);

temperaturetext[0]=showtemp[1]+48; // 1 + 48 = 49 = proper number for 1 in character
temperaturetext[1]=showtemp[2]+48;  // 7+ 48 = 55 or proper number for 7 in character
temperaturetext[2]=showtemp[3]+48; // etc
temperaturetext[3]=46; // 46 = proper number for a decimal.
temperaturetext[4]=showtemp[4]+48;  //etc
temperaturetext[5]=showtemp[5]+48;  //etc

 

the results in temperaturetext looks like {‘1′,’7′,’5′,’.’,’2′,’5′}

I roasted twice now using the new graph with actual temperatures listed up top and was planning on comparing the results but I accidentally corrupted the first file.  I’ve got one more batch of some coffee from Rwanda that I was testing with.  I’m getting pretty close to running out of coffee again so it’s time to order some more soon.  I was hoping to have something good from Ethiopia come up for sale but it’s still a little early for that.

Still working on… recognizing temperatures for various(rough) stages the roast is at vs some sort of mechanism to confirm a stage marking things like first / second etc.  Also need to get ambient weather information recorded and get other sensors going on it…. and make it pretier…. and of course get it hooked to higher voltage turning on and off the heat.

Writing to SD memory…

By | | , , , , , , ,
Leave a comment

Soo… the latest update… I had wired in the SD memory stick reader and had been testing it separate from the main roaster program. I’ve found having a “dedicated” programs for a particular sensor with the rest of the sensors and displays attached but not initialized has resulted in easier testing and troubleshooting.  Occasionally it works right away but other times conflicts come up.  Generally once I have manage to confirm it works without the other code running I at least have a reasonable assumption that it may actually work and is wired properly.   Since I’m pretty new to the whole wiring these things up it’s a pretty good idea to test my wiring out.  So far I’ve actually done pretty well reading enough about each sensor to figure out what I need to make it work the first time.  If I go too long not getting it to work I try to disconnect everything else and run it by itself which usually helps me identify conflicting pin usage that I didn’t see initially.

So far I tend to find issues with the LCD interface / graphic chip / memory config chip to conflict with a particular pin here and there.  If it works without the LCD boards attached it obviously has a much smaller number of pins from the new sensor to try to find a conflict with. Usually by the time I isolate the LCD away from the system I’ve managed to throw together code that works within minutes of starting things up again.
My last success with the SD memory was short lived because I discovered there were pins that I had not noticed on the SSD1926 that apparently do something even though I’m in 8 bit mode instead of 16 bit.  They seem to have ended up being connected when I was trying to check my Write Protect and Card Detect pins.   It took probably about 3 hours of looking at the schematic for the graphics board assembly to figure out which wires (15 minutes) it was and then find some (the rest of the time) that were not being used already.   Since I am using 8 bit communication instead of  the 16 bit mode I would have assumed them to be “dormant” and potentially available.   Not quite sure what is going on with that since I have not obtained the data sheet for the SSD1926 chip yet.

I had an unexpected guest show up early in the week and didnt get much time to work on this.  After making a few adjustments to the wiring I got it up and writing to the SD with the LCD attached.  This weekend I got it loaded inside the Coffee Roaster programming.  I ran into a few initialization problems that resulted in a momentary “stream of gibberish” coming out the UART port that I was using for watching status of some of the code I was troubleshooting with in a terminal window.  It seemed as if the system had a baud rate to the com port of the computer that suddenly “shifted” up and down a few times in the middle of the machine starting up and then returned to normal. After I removed some of the apparently duplicate excess code from the init area it resumed working normally.

I then had to move the “write to SD” down through the startup past the time and date retrieval area.  This results in accurate time/date stamps on the file now being written to the SD memory card.  I then began to modify the SD demo write into a command that builds the buffer data using a sprintf template inserting date and time on a line separated by commas and a few sections (with 0.00’s right now) for sensor data as well.  I’m going to bundle the write commands up into a function so that I can insert it into roaster loop as a external function.  Every time it samples the temperatures and other future sensors it will shove it into the call to the “write to SD” function where it will get formatted and append to the file it created during the initialization of a new roast loop.

As I said, I havent had much time to work on it this past week but probably tonight and tomorrow I’ll get significantly closer to figuring that part out and probably test running the roaster with nothing in it just to get some temperaturee logging as it goes up/down for a few seconds and then exit the roast to close it to check the accuracy. Then when I’m sure that’s working I’ll try to do a regular roast with it out in the kitchen and see if I can get “good numbers” that I can post.

If I can get that working then the next step will be to get a “file management” function going to come up with names of files to make them unique and maybe let me load the data into the system to preview it on a graph on the PIC32 LCD as well as delete files. THEN I get to start figuring out how to program it to control things by itself based on my normal data.  😀