So I previously had tried to get things working using a PIC24 and had both the thermocouple and a battery backed real time clock interfaced and communicating as well as some other items over SPI and I2C. Over time I decided I needed to focus on the PIC32 due to the memory, speed, and ease of interfacing with an LCD. I thus ordered the development kits for the PIC32 and a series of other parts and started this blog about them since I had to start over.
I have so far had tremendous problems with the I2C on the PIC32 hardware. In addition I seemed to show slightly more success with the other sensors over the RTC chip in particular. The RTC was provided by SparkFun as a breakout board. It does not have the pull up resistors on the break out board so it can be chained on to something that already has them… or else you need to insert your own resistors and power between the holes on the breakout board and the microprocessor pins.
After digging through an old box full of parts scavenged off of computers and an old 32 Port Audio Mixer that was destroyed while I was moving due to falling off the lift gate as I was finishing moving out of an old house I lived in. I’ve managed to create an I2C bus using a ribbon cable with some connectors pressed into it close together. I was then able to use a female header socket with some long pins and plug the DS1307 breakout into it for SDA and SCL. On the second connector I inject power into the other side of a header (the resistors are too thin to make contact in the normal connector for some reason). I then connect the third connector to the PIC32 pins using Female to Male jumper wire. Due to the length of the pins on the female header connectors I am able to clip the probes for a Logic Analyzer to the system.
After trying and trying and changing resistor values etc I was getting nowhere. I measure 5 volts on the I2C pins and with other sensors I could get confirmation of the bus going from on to off occasionally. With the RTC chip I was stuck at on. I had no idea what was happening and finally after several days of banging my head I yanked the backup battery out of the RTC.
Sparkfun claims that they have pre-programmed the time on the RTC and they are thus ready to be used/read etc without requiring time to be placed on the chip to start the oscillator. They also comment somewhere in the pages about how it should last about 9 years on the lithium battery provided blah blah. Apparently this is not entirely accurate. I have stumbled across several people commenting on the system NOT being programmed on their boards. In my case it turns out that the RTC chip simply is “hung” possibly caused by a malfunction of the battery. Upon removing the battery I noticed that it had “exploded” in one of the corners like they typically do when they get old. There was some rusted/acid crusted bits and leakage on the surface of the battery AND on the circuit board. I plugged it in again and ran some testing to it and it appeared to be accepting programming from the PIC32. After going to Radio Shack looking for a new battery I cleaned up the board and installed the new battery. The programming seems to stick now and all is well having provided a new battery. The old battery is currently reporting .8V instead of the normal 3.3v and is generally rusted and fouled up.
Unfortunately this story does not have freedom from flaws. It turns out that while running the routines normally I get results of either 0x0000 or 0x00FF. When I force it to debug mode, however, things appear normal displaying hours/minutes/seconds/date/month/year/etc in the appropriate slots and upon returning form debug mode back to normal show in the spaces I forced it to display the text. Further when I try to program it into a demo program Microchip wrote it seems as if the year is actually the “date”, the date is the “day of the week”, the month is the correct month, the hours and minutes dont make any sense. I’m not sure what is going on there. Taking a wild guess I’m thinking the date/year thing being weird is coincidental and that in reality there is perhaps some sort of Hex vs BCD problem going on.
Since I have achieved some level of success at this point though I am going to do a commit to the SVN repository on my server at home to make sure I don’t lose this code. I can see, with the Logic Analyzer, that the SCL and SDA pins switch from 0 to 5v and 5v to 0v from time to time so I know the pull up is functioning. What is troublesome is that the SCL pin never appears to have a functioning clock signal. Immediately after applying a Start command it appears to register a bus collision. I cannot figure out why this is happening and it further baffles me that I could program AND read I2C data without a functional I2C bus.
I was reading on the Microchip forums about how they, apparently, recently changed the I2C Library on the PIC32 making it function different than the PIC24. This is causing significant problems for PIC32 users. It seems to have something to do with the Idle state not being checked on the PIC32 causing collisions or something like that. How exactly this applies to what I’m doing I’m not sure because while the symptoms are the same it does not seem to follow the same circumstances.
In addition this weekend I obtained some LCD screen protectors (typically used for GPS) and removed the original covering provided by Microchip and installed the new protector. It is a lot smoother and easier to read the screen. I should be able to record the video on the screen without it being distorted once I get the I2C (and some SPI) sorted out and working.